Helpful information how sync BMW remote key (if that does not work, you need to repair your key) 1. With both keys, get in the car and close all windows and doors. 2. Put working key into the ignition and turn to position 1 (the accessories should turn on) 3. Turn the key back to position 0 and take the key out of the ignition. 4. Using the working key, hold down the unlock button, press the BMW logo (lock button) 3 times, and release the unlock button. Doors should lock and unlock. 5. With the new key, hold down the unlock button and press the BMW logo (lock button) 3 times and let go of the unlock button. Doors should lock and unlock and you’re done!!

TOYOTA REMOTE 2000 – 2005 Celica 2001 – 2003 Prius 2001 – 2005 ECHO 2001 – 2007 Highlander 2001 – 2008 RAV4 2002 – 2006 Camry 2003 – 2008 Avalon, Corolla and Matrix 2004 – 2008 Sienna and Solara 2005 – 2008 Tacoma 2007 – 2008 FJ Cruiser and Yaris – Driver’s door open and unlocked – Key out of ignition 1. Insert and remove the key from the ignition switch 2 times within 5 seconds NOTE: Steps 2 and 3 should be performed within 40 seconds 2. Close and open the driver’s door TWICE. 3. Insert the key into the ignition and remove it. NOTE: Steps 4-6 should be performed within 40 seconds 4. Close and open the driver’s door TWICE 5. Insert the key into the ignition 6. Close the door 7. Turn the ignition switch from “LOCK” to “ON” and back to “LOCK” at about 1 second intervals to select the desired mode from the list below: – 1 time for ADD mode – 2 times for REWRITE mode – 3 times for CONFIRMATION mode – 5 times for PROHIBITION mode 8. Remove the key from the ignition 9. To confirm your mode selection, the power locks will now cycle “lock” to “unlock a number of times corresponding to your key cycles in step 7. NOTE: If CONFIRMATION or PROHIBITION modes have been selected, opening the door will complete the procedure. 10. For ADD or REWRITE modes, do the following within 40 seconds of Door Lock confirmation; A – Press both transmitter LOCK and UNLOCK buttons simultaneously between 1 and 1.5 seconds and release. (I had to do this a few times because I held the buttons down longer than the 1-1.5 seconds) B – Within 3 seconds of step A, press the transmitter LOCK button from more than 1 second and release. > If the transmitter has been successfully programmed, the power locks will cycle “lock” to “unlock” once at this time. > If there are problems with the transmitter or the procedure up to this point, the locks will cycle twice. If this occurs, verify that you have received the correct transmitter, and then repeat the above procedure. C – If multiple remotes are to be reprogrammed, repeat steps A and B 11. Open to driver’s door to conclude programming mode 12. If you make an error during the programming mode, turn the ignition key to “ON” and back to “LOCK” to erase entered steps.

FORD REMOTE – THIS PROCEDURE RESETS ALL REMOTES FOR THE VEHICLE. ALL FUNCTIONING REMOTES WILL HAVE TO BE REPROGRAMMED DURING THE PROCEDURE There are a few different procedures that will program your remotes depending on what vehicle that you have. You can find your exact procedure in your owners manual. If you do not have your owners manual you can try any of the procedures below until you find the one that works for your vehicles Make sure that you don’t press the brake pedal at any time during or before the procedure. Procedure A: 1.Close all doors, then open drivers door and press the Unlock button on driver’s door while it is open, insert key into ignition. 2.Turn ignition from OFF to RUN 8 times within 8 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode. (if the door locks do not cycle, then it was done incorrectly. You must start over by removing key and beginning from step 1) (Off is the position where you can remove your key, RUN is the position just shy of starting your car.) 3.Within 10 seconds press any button on the first keyless remote to be programmed. Door locks will cycle to confirm programming. If you only have one remote then skip to step 5. 4.Within 10 seconds, press any button on the second keyless remote. Door locks will cycle again to confirm programming. Repeat step 4. for all other remotes. 5.Turn ignition to OFF. Locks will again cycle to indicate end of programming mode. *If this does not work try the procedure with the door closed. Procedure B: 1. Fasten seatbelt and close all doors 2. Turn the ignition from OFF to RUN 4 times within 3 seconds. 3. Turn the ignition OFF. The system will chime to confirm programming mode. 4. Within 10 seconds, press and hold any button on first keyless remote. The system will chime once to confirm programming. 5. Within 10 seconds, press and hold any button on second keyless remote. System will chime once to confirm programming. 6. Turn ignition to RUN to exit programming mode.

1. Turn the ignition switch from Position 0 to ON 6 times within 10 seconds. 2. Then turn ignition switch to OFF position. Leave key in ignition switch. 3. After 2 seconds, the system will enter programming mode and will flash the warning lights twice. 4. Press and HOLD the unlock button on the Plip. 5. While pressing the unlock button, press the lock button 3 times. 6. Release the unlock button. 7. The warning lights will flash once to indicate successful programming. 8. Repeat procedure 4 to 7 for up to 4 plip key’s. 9. When completed turn ignition ON, and the warning lights will flash 2 times. 10. Remove key, and check all plip key’s for operation.

1. Turn the Ignition ON. 2. Press and HOLD the LOCK button for 5 seconds. 3. Turn the Ignition OFF. 4. After 5 seconds test the key.

1. Turn the Ignition ON. 2. Press and HOLD the LOCK button for 5 seconds. 3. Turn the Ignition OFF. 4. After 5 seconds test the key.